AUTONET TV

Your Biggest Fan (Radiator Fan Problems)

Your vehicle's engine makes a lot of heat when it's powering you down the road, so it needs a way to get rid of that energy.  That's why your vehicle has a cooling system, complete with a radiator and one or two radiator fans, also called cooling fans.  Those fans make sure air keeps moving across the radiator so that the heat stored in the coolant can be dissipated outside when the vehicle is stopped or not traveling fast.

Radiator fans can develop problems and can stop working properly or stop working altogether.  Some signs to look for? If you're driving slowly and idling and you see your temperature gauge moving toward the red or hot zone, that could spell trouble.  Another thing you may notice when a radiator fan is failing is that there may be a loud noise coming from the engine compartment.

There are two types of radiator fans.  One is mechanically connected to the engine and uses the engine's rotational energy to turn it.  The other is an electric fan and is the type used in most newer vehicles.  In the electrical type, one of the components, such as a relay or fuse, may fail, causing the fan to stop turning.  In the mechanical type, since it's driven by a pulley/belt mechanism, one of those components may break or stop working properly.  A clutch can wear out or a belt may slip or break. 

When your cooling fan isn't working properly, it may cause your engine to overheat which could lead to expensive damage. That's why it's important to make sure you visit your service facility if you notice any of these symptoms.  A technician is trained to diagnose the problem and make sure your radiator fan is doing its job.  When it comes to your vehicle, your radiator fan really is your biggest fan.

Triple A Automotive
972 Barstow Suite B
Clovis, CA 93612
(559) 299-9300
http://www.tripleaautomotive.com

Such a Little Part (Climate Control Resistor)

You expect your heater/air conditioner to work like it should.  You have a control for temperature and one for fan speed.  You even have a control for what vents the air comes out of. 

Don't be surprised one day if your blower fan develops a mind of its own and starts going crazy.  Most of the time, you may find that it starts blowing at full speed, and nothing you do to try to control it does any good.  This is what may be happening.

Your blower motor has an electronic component called a resistor.  It does what its name says; it offers resistance.  When you want the fan to run more slowly, you turn the fan speed down.  That resistor accomplishes that by turning its resistance up.  When the resistor fails, the power has nothing to slow it and the fan speeds up. 

It's a small part and can fail due to age or corrosion.  It's usually not an expensive part, either, but it's often found in a location that's not that easy for the technician to get to.  That means labor costs will vary depending on the design of your vehicle. 

Occasionally, a faulty resistor can cause the blower motor not to work at all or only partially come on.  But other things can cause that as well, such as a faulty fan switch or vent control. 

This is where a technician's training comes in.  Special equipment can track down precisely where the issue is so you can be assured the correct part is being replaced.

It's just not pleasant when the blower motor isn't following orders.  Have your service facility check it out so you can be the blower's boss, like it should be. 

Triple A Automotive
972 Barstow Suite B
Clovis, CA 93612
(559) 299-9300
http://www.tripleaautomotive.com

Some New Boots (Suspension Maintenance)

There are some boots that don't come in a shoe box and aren't worn on your feet.  They are called axle or CV boots, and they can be important parts for many vehicles.

That CV stands for constant velocity.  CV axles are mainly used in front-wheel drive and all-wheel drive vehicles. They're also used in some rear-wheel drive vehicles with independent suspensions.  They have two CV joints, one inner and one outer, placed between the axle and the drive wheels.  That way the vehicle's engine power can drive the wheels, no matter what angle they are.  They also adjust for the different speeds wheels turn as they go around corners. 

Because roads are full of all sorts of hazards (dirt, oil, water, grime), these CV joints need to be protected.  They also have grease in them to keep the bearings moving smoothly.  That's the job of the rubber boots that are supposed to keep that debris out.  These CV or axle boots are made of rubber or plastic and usually last a long time without any problem.  But sometimes they fail, either from being hit by debris or age causing the rubber or plastic to deteriorate.  That can allow the grease to leak out of the joint and the moisture to get in.  And that's where the trouble is.

So it's important to have a vehicle's CV boots checked periodically, especially when they begin to have more than 100,000 miles/160,000 kilometers on them.  A technician inspects them for tears or cracks.  Sometimes if the problems are found early enough, the boots can be replaced and the joints can be re-packed with grease. 

But sometimes the CV joint can wear out even though the boot is intact.  When the CV joint fails, you might hear a grinding, humming or clicking noise and feel vibration.

Some of these can be difficult to access for service, so many service advisors will recommend replacing the joints and boots at the same time.  Just remember, new CV boots won't make a fashion statement, but they will keep your vehicle going down the road for years to come.

Triple A Automotive
972 Barstow Suite B
Clovis, CA 93612
(559) 299-9300
http://www.tripleaautomotive.com